【图文教程】数码视讯（完美星空）S6初步加强教程_中国移动魔百盒
只需一步，快速开始
扫一扫，访问微社区
后使用快捷导航没有帐号？
TV应用下载 / 资源分享区
综合交流 / 产品评测 / 活动公告
新手入门 / 社区互助
查看: 6151|回复: 278
欢迎加入移动破解交流群：，一起交流破解！&&
& &&&由于机型的小众和移动阉割的彻底，在求助淘宝加强和论坛借鉴无果的情况下，购入TTL线，借鉴坛友大辉哥啊和其他众多坛友的经验基础，总结出以下教程，本教程图片借鉴坛友，本教程仅仅局限于数码视讯（完美星空）S6的加强，方便大家共同研究，方便大家。
& && &该机顶盒采用卡扣连接，可以使用小一字螺丝刀或者拆机棒从USB口位置下手，很容易就拆开了，拆开底板后，使用小十字螺丝刀拆下主板上的3个螺丝，拿下主板，可以看见TTL插口，将TTL线以黑绿白的顺序连接插口（红线留空，主板插口第4针留空）。
1.png (533.89 KB, 下载次数: 2)
13:08 上传
游客，如果您要查看本帖隐藏内容请
正需要这个，谢谢楼主的分享！
怎么弄啊。
学习学习！
好&&谢谢 楼主
谢谢 楼主&&OKOKOKOKOK
增值电信业务经营许可证：浙B2- 丨 杭州市公安局滨江分局备案编号：71
Powered by Discuz!
监督举报：阅读权限70
在线时间 小时
此盒子目前只能在已经开通IPTV业务的联通宽带上使用，并且还要注册绑定等，否则啥也干不了。经楼主拆机观察，盒子硬件较强大，接口丰富，如果能刷个非定制的系统，当普通的用那就太好了。
Logo.jpg (111.24 KB, 下载次数: 2)
10:24 上传
Nameplate.jpg (301.12 KB, 下载次数: 1)
10:24 上传
Remote.jpg (213.09 KB, 下载次数: 1)
10:25 上传
IO.jpg (68.52 KB, 下载次数: 1)
10:24 上传
USB.jpg (44.91 KB, 下载次数: 1)
10:25 上传
PCB 1.jpg (3.09 MB, 下载次数: 2)
10:25 上传
PCB back.jpg (2.84 MB, 下载次数: 1)
10:25 上传
RTL8188ETV.jpg (144.56 KB, 下载次数: 1)
10:25 上传
K4B2G1646Q-BCK0.jpg (162.31 KB, 下载次数: 1)
10:24 上传
KH25L1606EM2I.jpg (246.71 KB, 下载次数: 1)
10:24 上传
阅读权限70
在线时间 小时
本帖最后由 kamine 于
10:30 编辑
以下是启动过程
BOOT_OK!Pdecomp
_done
[AT][MB][start ub][0]
U-Boot 2011.06-svn107700 (Aug 29 2015 - 16:53:28)
CPU&&: Kaiser
Board: BD_MST170A_D01A_SZ
Hello U-Boot
DRAM:&&480 MiB
SPI:&&Flash is detected (0x, 0x20, 0x15)
MDrv_SERFLASH_GetInfo()
& && &&&u32AccessWidth = 1
& && &&&u32TotalSize& &= 2097152
& && &&&u32SecNum& && &= 32
& && &&&u32SecSize& &&&= 65536
uboot held at [3ccddf60~3e000000]
Now running in RAM - U-Boot at: 3d100000
MMC:& & eMMC 3775MB [75FFF8h]
In:& & serial
Out:& &serial
Err:& &serial
Net:& &No ethernet found.
Get MAC from ethaddr env
MAC:&&0x0: 0x24: 0x68: 0xc5:0x8c: 0x6c
MIU BASE =0x&&addr =0x1da96ed8
MIU BASE =0x&&addr =0x1da96ed8
It's the last cmd
[COPRO] HAL_COPRO_RegSetBase: u32NonPMBaseAdd = 0x1F200000
[url=home.php?mod=space&uid=1282221]@@@@@@[/url] u32CpuSpeedMHz= 1152 MHz
Init work status led & network status led!
workled set high
IR led set low
network ok led set low
network ng led set high
WIFI POWE EN set low
MIU BASE =0x&&addr =0x0
MIU BASE =0x&&addr =0x0
Wait for PM51 standby...........PM51 run ok...........============= set bootargs ===============
Unknown command 'if_51OnRam_set' - try 'help'
MDrv_PNL_Init u32PnlRiuBaseAddr = 1f200000
MDrv_PNL_Init u32PMRiuBaseAddr = 1f000000
[_MDrv_PNL_Init_LPLL][294]pPNL_DeviceId-&u32Id=0, pstPanelInitData-&u16Width=1280, pstPanelInitData-&u16Height=720
[_MDrv_PNL_Init_LPLL][296]u16HTotal=1980,u16VTotal=750,pstPanelInitData-&u16HTotal=1980,pstPanelInitData-&u16VTotal=750, u16DefaultVFreq=500
[_MDrv_PNL_Init_Output_Dclk][339]pPNL_DeviceId-&u32Id=0, pstPanelInitData-&u16Width=1280, pstPanelInitData-&u16Height=720
[_MDrv_PNL_Init_Output_Dclk][341]u16HTotal=1980,u16VTotal=750,pstPanelInitData-&u16HTotal=1980,pstPanelInitData-&u16VTotal=750, u16DefaultVFreq=500
[_MDrv_PNL_Init_LPLL][294]pPNL_DeviceId-&u32Id=1, pstPanelInitData-&u16Width=1280, pstPanelInitData-&u16Height=720
[_MDrv_PNL_Init_LPLL][296]u16HTotal=1980,u16VTotal=750,pstPanelInitData-&u16HTotal=1980,pstPanelInitData-&u16VTotal=750, u16DefaultVFreq=500
[_MDrv_PNL_Init_Output_Dclk][339]pPNL_DeviceId-&u32Id=1, pstPanelInitData-&u16Width=1280, pstPanelInitData-&u16Height=720
[_MDrv_PNL_Init_Output_Dclk][341]u16HTotal=1980,u16VTotal=750,pstPanelInitData-&u16HTotal=1980,pstPanelInitData-&u16VTotal=750, u16DefaultVFreq=500
[COPRO] HAL_COPRO_RegSetBase: u32NonPMBaseAdd = 0x1F200000
hdmitx/mstar/MsDrvHdmi.c getRxVideoFormatFromEDID 490 FAIL!
hdmitx/mstar/MsDrvHdmi.c msHdmitx_Init 638:&&bEDIDRet:0, s8Format:-1
Create Dolby verifier task failed!![Hal_VE_EnableDI][1028] bEnable = 0, bIsDNR2VE = 0
[msHdmitx_Init][751]This CHIP ONLY support YUV out!
setHDMITxAnalogTuning: Error: MApi_HDMITx_GetRxDCInfoFromEDID EDID is not ready, at 361
msHdmitx_Init: Error: MApi_HDMITx_EdidChecking FAILE! use 1080p default, at 768
[ eMMC_CMD18_MIU() ] eMMC WARN: CMD18 Reg.12: FC61h, Err: 0h, Retry: 1
eMMC retry by DATA_SYNC: 40h, ori:15h
[AutoTest][MBoot][JPD Decode]
mmc change mount : tvservice
Size of file &/config/mmap.ini& from mmc device 0 partition tvservice: 48978 bytes
Loading file &/config/mmap.ini& at offset 0x0 from mmc device 0 partition tvservice
48978 bytes read
[GOP2, PID 0, TID 0x-1][Driver Version]: 0089, BuildNum: 0002, ChangeList:
[GOP5, PID 0, TID 0x-1][Driver Version]: 0089, BuildNum: 0002, ChangeList:
[HAL_GOP_GWIN_SetDstPlane][852]====GOP5gogo!!!!===
[HAL_GOP_EnableSCPerPixelNewAlphaMode][940]====enable_new alpha====
[HAL_GOP_GWIN_SetDstPlane][852]====GOP5gogo!!!!===
[AutoTest][MBoot][Show Logo][0]
Hit any key to stop autoboot:&&0
.....................fore uup IRKey [0xff]
## Booting kernel from Legacy Image at
...
& &Image Name:& &MStar-linux
& &Image Type:& &ARM Linux Multi-File Image (uncompressed)
& &Data Size:& & 3972222 Bytes = 3.8 MiB
& &Load Address:
& &Entry Point:&&
& &Contents:
& && &Image 0: 3785716 Bytes = 3.6 MiB
& && &Image 1: 186494 Bytes = 182.1 KiB
## Loading init Ramdisk from multi component Legacy Image at
...
-usb_stop(USB_PORT0)
-usb_stop(USB_PORT1)
& &Loading Multi-File Image ... MIU BASE =0x&&addr =0x500004c
MIU BASE =0x&&addr =0x500004c
MIU BASE =0x&&addr =0x208000
MIU BASE =0x&&addr =0x208000
OK
[AT][MB][start kr][0]
Starting kernel& &...
Uncompressing Linux... done, booting the kernel.
KERN-3.1.10.
[& & 0.000000] Initializing cgroup subsys cpu
[& & 0.000000] Linux version 3.1.10 () (gcc version 4.5.1 (Sourcery G++ Lite ) ) #2 SMP PREEMPT Sat Aug 29 16:56:39 CST 2015
[& & 0.000000] CPU: ARMv7 Processor [413fc090] revision 0 (ARMv7), cr=18c53c7d
[& & 0.000000] CPU: VIPT nonaliasing data cache, VIPT aliasing instruction cache
[& & 0.000000] Machine: kaiser
[& & 0.000000] GMAC_MEM= 0xx100000
[& & 0.000000]
[& & 0.000000] LX_MEM&&= 0xx
[& & 0.000000] LX_MEM2 = 0xAx1A700000
[& & 0.000000] LX_MEM3 = 0x0, 0x0
[& & 0.000000] EMAC_LEN= 0x100000
[& & 0.000000] DRAM_LEN= 0x
[& & 0.000000] Memory policy: ECC disabled, Data cache writealloc
[& & 0.000000] PERCPU: Embedded 8 pages/cpu @c12a r u32768
[& & 0.000000] Built 1 zonelists in Zone order, mobility grouping on.&&Total pages: 173388
[& & 0.000000] Kernel command line: console=ttyS0,115200 androidboot.console=ttyS0 root=/dev/ram rw rootwait init=/init LX_MEM=0x EMAC_MEM=0x100000 GMAC_MEM=0xx100000 DRAM_LEN=0x LX_MEM2=0xAx1A700000 LX_MEM3=0xCx0 CORE_DUMP_PATH=/data/core_dump.%p.gz resolution=DACOUT_720P_50 reproducerate=0 delaylogo=true BOOTLOGO_IN_MBOOT ENV_VAR_OFFSET=0x1E0000 ENV_VAR_SIZE=0x10000 ENV=SERIAL SECURITY=OFF BOOTTIME_SBOOT=0 BOOTTIME_UBOOT=0
[& & 0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes)
[& & 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
[& & 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
[& & 0.000000] Memory: 276MB 423MB = 699MB total
[& & 0.000000] Memory: 8480k available, 17296k reserved, 0K highmem
[& & 0.000000] Virtual kernel memory layout:
[& & 0.000000]& &&&vector&&: 0xffff0000 - 0xffff1000& &(& &4 kB)
[& & 0.000000]& &&&fixmap&&: 0xfff00000 - 0xfffe0000& &( 896 kB)
[& & 0.000000]& &&&DMA& &&&: 0xffc00000 - 0xffe00000& &(& &2 MB)
[& & 0.000000]& &&&vmalloc : 0xec000000 - 0xf8000000& &( 192 MB)
[& & 0.000000]& &&&lowmem&&: 0xc0000000 - 0xebb00000& &( 699 MB)
[& & 0.000000]& &&&pkmap& &: 0xbfe00000 - 0xc0000000& &(& &2 MB)
[& & 0.000000]& &&&modules : 0xbf000000 - 0xbfe00000& &(&&14 MB)
[& & 0.000000]& && & .text : 0xc0008000 - 0xc0722000& &(7272 kB)
[& & 0.000000]& && & .init : 0xc0722000 - 0xc076a700& &( 290 kB)
[& & 0.000000]& && & .data : 0xc076c000 - 0xc07a6ac8& &( 235 kB)
[& & 0.000000]& && &&&.bss : 0xc07a6aec - 0xc0996140& &(1982 kB)
[& & 0.000000] SLUB: Genslabs=13, HWalign=32, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
[& & 0.000000] Preemptible hierarchical RCU implementation.
[& & 0.000000] NR_IRQS:256 nr_irqs:256 256
[& & 0.000000] Global Timer Frequency = 492 MHz
[& & 0.000000] CPU Clock Frequency = 984 MHz
[& & 0.000000] fre = , mult= -, shift= 30
[& & 0.000000] sched_clock: 32 bits at 492MHz, resolution 2ns, wraps every 8729ms
[& & 0.000000]
[& & 0.000000] set_timeout, 278 @cpu0, set timeout register
[& & 0.000000] [AT][KR][reset timer][0]
[& & 0.000000] Console: colour dummy device 80x30
[& & 0.000000] console [ttyS0] enabled
[& & 0.273923] Calibrating delay loop... 1945.60 BogoMIPS (lpj=3891200)
[& & 0.296403] pid_max: default: 32768 minimum: 301
[& & 0.301589] Mount-cache hash table entries: 512
[& & 0.307294] Initializing cgroup subsys debug
[& & 0.311699] Initializing cgroup subsys cpuacct
[& & 0.316267] Initializing cgroup subsys freezer
[& & 0.320877] CPU: Testing write buffer coherency: ok
[& & 0.325954] ftrace: allocating 24991 entries in 74 pages
[& & 0.368476] before forking init thread, kernel takes about
ms
[& & 0.375395]
[& & 0.375405]&&Kernel_Level test
[& & 0.380157] smp_twd: clock not found: -2
[& & 0.384154] Calibrating local timer... 491.78MHz.
[& & 0.409327] hw perfevents: enabled with ARMv7 Cortex-A9 PMU driver, 7 counters available
[& & 0.465500] pen_release = 0x, addr= 0xc07a5444, pen_release ptr = 0x
[& & 0.465510]&&CPU1: Booted secondary processor
[& & 0.493258] CPU1: Unknown IPI message 0x1
[& & 0.501311] Brought up 2 CPUs
[& & 0.504327] SMP: Total of 2 processors activated (3905.53 BogoMIPS).
[& & 0.512173] devtmpfs: initialized
[& & 0.529998] NET: Registered protocol family 16
[& & 0.546032] L310 cache controller enabled
[& & 0.550109] l2x0: 8 ways, CACHE_ID 0x, AUX_CTRL 0x, Cache size: 524288 B
[& & 0.558242] hw-breakpoint: found 6 breakpoint and 1 watchpoint registers.
[& & 0.565059] hw-breakpoint: 1 breakpoint(s) reserved for watchpoint single-step.
[& & 0.572410] hw-breakpoint: maximum watchpoint size is 4 bytes.
[& & 0.607048] bio: create slab &bio-0& at 0
[& & 0.612523] SCSI subsystem initialized
[& & 0.617821] usbcore: registered new interface driver usbfs
[& & 0.623711] usbcore: registered new interface driver hub
[& & 0.629493] usbcore: registered new device driver usb
[& & 0.635835] eMMC: has SD,
[& & 0.639546] [ eMMC_pads_switch() Ln.7024 ]
[& & 0.643584] eMMC Err: unknown interface: 0
[& & 0.648788] Advanced Linux Sound Architecture Driver Version 1.0.24.
[& & 0.656289] Switching to clocksource timer1
[& & 0.660552] stop_machine_cpu_stop smp=0
[& & 0.660561] stop_machine_cpu_stop smp=1
[& & 0.707641] NET: Registered protocol family 2
[& & 0.712195] IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
[& & 0.719750] TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
[& & 0.729283] TCP bind hash table entries: 65536 (order: 7, 786432 bytes)
[& & 0.737010] TCP: Hash tables configured (established 131072 bind 65536)
[& & 0.743648] TCP reno registered
[& & 0.744876] [mmc]:mmc_decode_cid:113 cid.prv 0x2
[& & 0.744983] [mmc]:mmc_read_ext_csd:287 ext_csd.sectors 0x760000 prod_name 004GE0 BOOT_MULTI 0x10
[& & 0.745107] mmc0: new high speed MMC card at address 0001
[& & 0.765712] UDP hash table entries: 512 (order: 2, 16384 bytes)
[& & 0.771711] [mmc]:mmc_rescan_try_freq:1900 mmc0: eMMC completed
[& & 0.771722] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)
[& & 0.772008] NET: Registered protocol family 1
[& & 0.788714] RPC: Registered named UNIX socket transport module.
[& & 0.794695] RPC: Registered udp transport module.
[& & 0.799424] RPC: Registered tcp transport module.
[& & 0.804150] RPC: Registered tcp NFSv4.1 backchannel transport module.
[& & 0.810888] Trying to unpack rootfs image as initramfs...
[& & 0.826866] Freeing initrd memory: 180K
[& & 0.830799] NetWinder Floating Point Emulator V0.97 (extended precision)
[& & 0.837610] PMU: registered new PMU device of type 0
[& & 0.910067]&&Creating worker thread
[& & 0.913672]&&Succsesfuly Created
[& & 0.939881] ashmem: initialized
[& & 0.958239] squashfs: version 4.0 () Phillip Lougher
[& & 0.966125] Installing knfsd (copyright (C) 1996 ).
[& & 0.973938] NTFS driver 2.1.30 [Flags: R/O].
[& & 0.978874] ROMFS MTD (C) 2007 Red Hat, Inc.
[& & 0.983447] fuse init (API version 7.17)
[& & 0.988985] msgmni has been set to 1364
[& & 0.994073] io scheduler noop registered
[& & 0.998033] io scheduler deadline registered
[& & 1.002436] io scheduler cfq registered (default)
[& & 1.007654] Serial:
driver, 4 ports, IRQ sharing disabled
[& & 1.014326] serial8250: ttyS0 at I/O 0xfd201300 (irq = 192) is a 16550
[& & 1.021256] serial8250: ttyS1 at I/O 0xfd220c00 (irq = 231) is a 16550
[& & 1.028146] serial8250: ttyS2 at I/O 0xfd220d00 (irq = 242) is a 16550
[& & 1.046939] brd: module loaded
[& & 1.056194] loop: module loaded
[& & 1.060680] nbd: registered device at major 43
[& & 1.076856] PPP generic driver version 2.4.2
[& & 1.081712] PPP Deflate Compression module registered
[& & 1.086802] PPP BSD Compression module registered
[& & 1.092233] PPP MPPE Compression module registered
[& & 1.097064] NET: Registered protocol family 24
[& & 1.101608] tun: Universal TUN/TAP device driver, 1.6
[& & 1.106689] tun: (C)
Max Krasnyansky &&
[& & 1.113480] MStar xHCI init...
[& & 1.116619] xHCI_560000
[& & 1.119159] Mstar-xhci-1 H.W init
[& & 1.122500] Mstar_xhc_init version:
[& & 1.139829] BC disable
[& & 1.142308] Mstar-xhci-1 Mstar-xhci-1.0: Mstar xHCI Host Controller
[& & 1.148625] Mstar-xhci-1 Mstar-xhci-1.0: new USB bus registered, assigned bus number 1
[& & 1.156816] Mstar-xhci-1 Mstar-xhci-1.0: irq 222, io mem 0xfd320000
[& & 1.163213] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[& & 1.170035] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[& & 1.177286] usb usb1: Product: Mstar xHCI Host Controller
[& & 1.182709] usb usb1: Manufacturer: Linux 3.1.10 mstar_xhci_hcd
[& & 1.188653] usb usb1: SerialNumber: mstar
[& & 1.193504] hub 1-0:1.0: USB hub found
[& & 1.197309] hub 1-0:1.0: 1 port detected
[& & 1.201748] Mstar-xhci-1 Mstar-xhci-1.0: Mstar xHCI Host Controller
[& & 1.208064] Mstar-xhci-1 Mstar-xhci-1.0: new USB bus registered, assigned bus number 2
[& & 1.216100] usb usb2: New USB device found, idVendor=1d6b, idProduct=0003
[& & 1.222924] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[& & 1.230178] usb usb2: Product: Mstar xHCI Host Controller
[& & 1.235602] usb usb2: Manufacturer: Linux 3.1.10 mstar_xhci_hcd
[& & 1.241548] usb usb2: SerialNumber: mstar
[& & 1.246362] hub 2-0:1.0: USB hub found
[& & 1.250163] hub 2-0:1.0: 1 port detected
[& & 1.255390] mousedev: PS/2 mouse device common for all mice
[& & 1.262757] lirc_dev: IR Remote Control driver registered, major 253
[& & 1.269242] IR NEC protocol handler initialized
[& & 1.273799] IR RC5(x) protocol handler initialized
[& & 1.278614] IR RC6 protocol handler initialized
[& & 1.283167] IR JVC protocol handler initialized
[& & 1.287720] IR Sony protocol handler initialized
[& & 1.292360] IR RC5 (streamzap) protocol handler initialized
[& & 1.297956] IR MCE Keyboard/mouse protocol handler initialized
[& & 1.303872] IR LIRC bridge handler initialized
[& & 1.308345] Linux video capture interface: v2.00
[& & 1.313155] gspca: v2.13.0 registered
[& & 1.317065] usbcore: registered new interface driver uvcvideo
[& & 1.322842] USB Video Class driver (1.1.1)
[& & 1.328136] device-mapper: uevent: version 1.0.3
[& & 1.333474] device-mapper: ioctl: 4.21.0-ioctl () initialised:
[& & 1.342267] mmcblk0: mmc0: 3.68 GiB
[& & 1.347014] mmcblk0boot0: mmc0: partition 1 2.00 MiB
[& & 1.353214] mmcblk0boot1: mmc0: partition 2 2.00 MiB
[& & 1.359801] emmc_partition()
[& & 1.363554]&&[emmc]Start_block=14336, block_count=1024
[& & 1.368769] Start_block=15360, block_count=16384
[& & 1.373414] Start_block=31744, block_count=8192
[& & 1.377971] Start_block=39936, block_count=1040384
[& & 1.382788] Start_block=1080320, block_count=4194304
[& & 1.387779] Start_block=5274624, block_count=1048576
[& & 1.392770] Start_block=6323200, block_count=1048576
[& & 1.398505] Start_block=7371776, block_count=122880
[& & 1.403418] Start_block=7494656, block_count=32768
[& & 1.408237] Start_block=7527424, block_count=16384
[& & 1.413055] Start_block=7543808, block_count=4096
[& & 1.417785]
[& & 1.419281]&&mmcblk0: p1 p2 p3 p4 p5 p6 p7 p8 p9 p10 p11emmc_partition()
[& & 1.x0
[& & 1.434170]&&mmcblk0boot1: unknown partition table
[& & 1.439979] emmc_partition()
[& & 1.x0
[& & 1.446451]&&mmcblk0boot0: unknown partition table
[& & 1.452673] usbcore: registered new interface driver usbhid
[& & 1.458281] usbhid: USB HID core driver
[& & 1.462962] logger: created 256K log 'log_main'
[& & 1.467805] logger: created 256K log 'log_events'
[& & 1.472831] logger: created 256K log 'log_radio'
[& & 1.477753] logger: created 256K log 'log_system'
[& & 1.483610] Mstar_emac: [ PHY Addr ] ==& :0
[& & 1.487884] Mstar_emac: alloRAM_VA_BASE = 0xEC200000 alloRAM_PA_BASE= 0x&&alloRAM_SIZE= 0x100000
[& & 1.498273] RBQP_BASE =
[& & 1.502548] && [sdmmc] ms_sdmmc Driver Initializing...
[& & 1.508468] && [sdmmc_0] Get CD =& (0)
[& & 1.512279] && [sdmmc_0] CDZ use Ext GPIO IRQ: 217
[& & 1.517103] && [sdmmc_0] Probe Devices...(Ret:0)
[& & 1.524952] [][MAD_ALSA][001709]& &&&&6&Linux Kernel Version : 3.1.10
[& & 1.532300] [][MAD_ALSA][001710]& &&&&6&ALSA Kernel Version : 1.0.24
[& & 1.539554] [][MAD_ALSA][001711]& &&&&6&MStar ALSA Driver Version : 3.1.5
[& & 1.547238] [][MAD_ALSA][001712]& &&&&6&Initiate MStar ALSA driver engine
[& & 1.554926] [][MAD_ALSA][001581]& &&&&6&Go to register MStar ALSA driver
[& & 1.564661] [][MAD_ALSA][001645]& &&&&6&MStar ALSA driver is registered to slot 0
[& & 1.573290] [][MAD_ALSA][001916]& &&&&6&Initiate MStar ALSA core driver (customized)
[& & 1.581948] [][MAD_ALSA][000279]& &&&&6&Hal Driver 'MAD KAISER' is hooked.
[& & 1.589723] [][MAD_ALSA][000280]& &&&&6&MStar Core Version : 3.1.5
[& & 1.597956] Mstar_gmac: Wrong PHY Addr, maybe MoCA?
[& & 1.602920] Mstar_gmac: alloRAM_VA_BASE = 0xEC400000 alloRAM_PA_BASE= 0x&&alloRAM_SIZE= 0x100000
[& & 1.614634] MStar SATA Host Controller Probe
[& & 1.619948] scsi0 : mstar_sata
[& & 1.623674] ata1: SATA max UDMA/133 irq 229
[& & 1.630966] usbcore: registered new interface driver snd-usb-audio
[& & 1.637247] ALSA device list:
[& & 1.640225]& &#0: MStar MPEG Audio Decoder No.00
[& & 1.645368] oprofile: using arm/armv7-ca9
[& & 1.649788] oprofile: using timer interrupt.
[& & 1.654107] AOP:Oprofile Driver init done
[& & 1.658277] Netfilter messages via NETLINK v0.30.
[& & 1.663089] nf_conntrack version 0.5.0 (10916 buckets, 43664 max)
[& & 1.669781] ctnetlink v0.93: registering with nfnetlink.
[& & 1.675130] NF_TPROXY: Transparent proxy support initialized, version 4.1.0
[& & 1.682118] NF_TPROXY: Copyright (c)
BalaBit IT Ltd.
[& & 1.688636] ip_tables: (C)
Netfilter Core Team
[& & 1.694143] TCP cubic registered
[& & 1.698886] NET: Registered protocol family 10
[& & 1.704398] ip6_tables: (C)
Netfilter Core Team
[& & 1.709842] IPv6 over IPv4 tunneling driver
[& & 1.715048] NET: Registered protocol family 17
[& & 1.719570] NET: Registered protocol family 15
[& & 1.724195] Bridge firewalling registered
[& & 1.21q: 802.1Q VLAN Support v1.8
[& & 1.732485] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 3
[& & 1.742510] drivers/rtc/hctosys.c: unable to open rtc device (rtc0)
[& & 1.749026] [SERIAL INPUT MANAGE] Managed tty_struct(.name:ttyS0) Setup!!!
[& & 1.756024] [SERIAL INPUT MANAGE] disable_serial : ~~bye(len:5)
[& & 1.761975] [SERIAL INPUT MANAGE] enable_serial : (len: 0)
[& & 1.767485] [KDEBUGD] enter : _MStar
[& & 1.767489]
[& & 1.948378] ata1: SATA link down (SStatus 0 SControl 300)
[& & 1.954106] Freeing init memory: 288K
[& & 1.959224] [SERIAL INPUT MANAGE] Managed tty_struct(.name:ttyS0) is freed !!!
[& & 1.969703] init (1): /proc/1/oom_adj is deprecated, please use /proc/1/oom_score_adj instead.
[& & 2.111248] init: could not open /dev/keychord
[& & 2.115952] [SERIAL INPUT MANAGE] Managed tty_struct(.name:ttyS0) Setup!!!
[& & 2.122961] [SERIAL INPUT MANAGE] disable_serial : ~~bye(len:5)
[& & 2.128915] [SERIAL INPUT MANAGE] enable_serial : (len: 0)
[& & 2.134425] [KDEBUGD] enter : _MStar
[& & 2.134429]
[& & 2.139699] [SERIAL INPUT MANAGE] Managed tty_struct(.name:ttyS0) is freed !!!
[& & 2.147061] [SERIAL INPUT MANAGE] Managed tty_struct(.name:ttyS0) Setup!!!
[& & 2.154061] [SERIAL INPUT MANAGE] disable_serial : ~~bye(len:5)
[& & 2.160010] [SERIAL INPUT MANAGE] enable_serial : (len: 0)
[& & 2.165554] [KDEBUGD] enter : _MStar
[& & 2.165559]
& && && && & A N D R O I D
[& & 2.180422] [SERIAL INPUT MANAGE] Managed tty_struct(.name:ttyS0) is freed !!!
[& & 2.187722] init: open /dev/block/mmcblk0boot1 accret:0
[& & 2.195405] init: open /dev/block/mmcblk0boot1 accret:0
[& & 2.201549] init: mac: 00:24:68:c5:8c:6c
[& & 2.205515] init: sn: 40435
[& & 2.209388] init: pangym serialno readret = 00:24:68:c5:8c:6c
[& & 2.215254] init: pangym serialno sn = 40435
[& & 2.220719] init: serialno stbid = C
[& & 2.262943] EXT4-fs (mmcblk0p4): mounted filesystem with ordered data mode. Opts: journal_checksum
[& & 2.329453] EXT4-fs (mmcblk0p5): recovery complete
[& & 2.334606] EXT4-fs (mmcblk0p5): mounted filesystem with ordered data mode. Opts: journal_checksum
[& & 2.357624] EXT4-fs (mmcblk0p7): recovery complete
[& & 2.362770] EXT4-fs (mmcblk0p7): mounted filesystem with ordered data mode. Opts: journal_checksum
[& & 2.378276] EXT4-fs (mmcblk0p8): mounted filesystem with ordered data mode. Opts: journal_checksum
[& & 2.399889] EXT4-fs (mmcblk0p9): recovery complete
[& & 2.405039] EXT4-fs (mmcblk0p9): mounted filesystem with ordered data mode. Opts: journal_checksum
[& & 2.439555] EXT4-fs (mmcblk0p10): recovery complete
[& & 2.444793] EXT4-fs (mmcblk0p10): mounted filesystem with ordered data mode. Opts: journal_checksum
[& & 2.477610] UMP: UMP device driver&&loaded
[& & 2.558349] Mali: Mali device driver loaded
:/ $ TVOS *checkPoint*
复制代码
J1.jpg (172.71 KB, 下载次数: 1)
10:30 上传
阅读权限70
在线时间 小时
一些硬件信息
:/proc $ cat cpuinfo& && && && && && && && && && && && && && &&&
Processor& && & : ARMv7 Processor rev 0 (v7l)
processor& && & : 0
BogoMIPS& && &&&: 1945.60
processor& && & : 1
BogoMIPS& && &&&: 1959.93
Features& && &&&: swp half thumb fastmult vfp edsp neon vfpv3 tls
CPU implementer : 0x41
CPU architecture: 7
CPU variant& &&&: 0x3
CPU part& && &&&: 0xc09
CPU revision& & : 0
Hardware& && &&&: kaiser
Revision& && &&&: 0020
Serial& && && & : 0000
:/proc $ cat meminfo& && && && && && && && && && && && && && && &
MemTotal:& && && &698948 kB
MemFree:& && && & 396092 kB
Buffers:& && && && &3824 kB
Cached:& && && &&&125504 kB
SwapCached:& && && && &0 kB
Active:& && && &&&120408 kB
Inactive:& && && &113720 kB
Active(anon):& &&&105056 kB
Inactive(anon):& &&&3048 kB
Active(file):& && &15352 kB
Inactive(file):& &110672 kB
Unevictable:& && && &228 kB
Mlocked:& && && && && &0 kB
HighTotal:& && && && & 0 kB
HighFree:& && && && &&&0 kB
LowTotal:& && && &698948 kB
LowFree:& && && & 396092 kB
SwapTotal:& && && && & 0 kB
SwapFree:& && && && &&&0 kB
Dirty:& && && && && & 24 kB
Writeback:& && && && & 0 kB
AnonPages:& && &&&105032 kB
Mapped:& && && && &61124 kB
Shmem:& && && && &&&3076 kB
Slab:& && && && &&&10276 kB
SReclaimable:& && & 3660 kB
SUnreclaim:& && && &6616 kB
KernelStack:& && &&&3488 kB
PageTables:& && && &8712 kB
NFS_Unstable:& && && & 0 kB
Bounce:& && && && && & 0 kB
WritebackTmp:& && && & 0 kB
CommitLimit:& && &349472 kB
Committed_AS:& & 3691316 kB
VmallocTotal:& &&&196608 kB
VmallocUsed:& && & 26008 kB
VmallocChunk:& &&&153540 kB
:/proc $ 复制代码
阅读权限70
在线时间 小时
Kaiser命令列表（类似CFE）
Kaiser# ?
?& && & - alias for 'help'
ac& && &- set a new config to the bootargs
add_autotest- add_autotest& &- Perform autotest
add_hsl - add_hsl& &- autotest with hsl
base& & - print or set address offset
bdinfo&&- print Board Info structure
bin2emmc- bin2emmc - read bin file and restore it to emmc
boot& & - boot default, i.e., run 'bootcmd'
bootargs_set- Set info exchange and set to boot args.
bootcheck- bootcheck& &- Do boot check
bootd& &- boot default, i.e., run 'bootcmd'
bootlogo- bootlogo& &- Display Logo_Music
bootm& &- boot application image from memory
bootmusic- bootmusic& &- play music
bootp& &- boot image via network using BOOTP/TFTP protocol
checkfile- check file exist in u disk,and set the partition.
cmp& &&&- memory compare
config2env- Set config to environment.
config_raw_io- Config the target device for raw I/O
coninfo - print console devices and information
cp& && &- memory copy
crc32& &- checksum calculation
custar&&- do usb update from the specified file that is in usb.
dbg& &&&- set debug message level. Default level is INFO
dbtable_init- dbtable_init& &- let data&&is ready (logo, music, panel, ursa).
dc& && &- delete the specific cofig that is in the bootargs
delay& &- delay time, time unit is ms
destroy_logo- destroy_logo - Stop logo display
dhcp& & - boot image via network using DHCP/TFTP protocol
dont_overwrite- This serial apis are for protecting the specific partitions are overwrited. ex: customer
This cmd is used to register which partition should not be overwrite
dont_overwrite_free- This serial apis are for protecting the specific partitions are overwrited. ex: customer
This cmd is used to free all registered partitions.
dont_overwrite_init- This serial apis are for protecting the specific partitions are overwrited. ex: customer
This cmd is used to init this function
du& && &- du&&- Disable UART
ebist& &- PHY loopback test
echo& & - echo args to console
editenv - edit environment variable
edump& &- EMAC Register settings dump
eloopback- Long loopback test
emmc& & - eMMC sub system
emmcbin - emmcbin - dump emmc and restore it to fat usb disk
emmcbootbin- emmcbootbin - dump emmc boot partition and write it to fat usb disk
env& &&&- environment handling commands
envload - envload& &- reload the nand environment.
estart&&- EMAC start
exit& & - exit script
ext2load- load binary file from a Ext2 filesystem
ext2ls&&- list files in a directory (default /)
ext4filesize- get file size from a Ext4 filesystem
ext4load- load binary file from a Ext4 filesystem
ext4ls&&- list files in a directory (default /)
ext4partload- part load binary file from a Ext4 filesystem
ext4write- create a file in the root directory
false& &- do nothing, unsuccessfully
fatfilesize- fatfilesize - load binary file from a dos filesystem
fatinfo - print information about filesystem
fatload - load binary file from a dos filesystem
fatls& &- list files in a directory (default /)
fatpartload- fatpartload - load binary file from a dos filesystem
fatwrite- fatwrite - write binary file to a dos filesystem
filelist- Dump the file list.
filelisttest- This command is only for file list test
filepartload- load part of a file to RAM
get_mboot_config- get mboot config from binary coverted from mboot_config.ini
get_mmap- get memory info from supernova's mmap
go& && &- start application at address 'addr'
hdmi& & - hdmi&&-
help& & - print command description/usage
if_boot_to_pm- if boot to PM
iminfo&&- print header information for application image
imxtract- extract a part of a multi-image
initDbgLevel- Initial varaible 'dbgLevel'
init_raw_io- init raw_io module
itest& &- return true/false on integer compare
kernelProtect- kernelProtect&&- Protect kernel
kernelProtectBist- kernelProtectBist&&- Protect kernel bist
led& &&&- See led commands
loadb& &- load binary file over serial line (kermit mode)
loads& &- load S-Record file over serial line
loadspi - load data from SPI
loady& &- load binary file over serial line (ymodem mode)
loop& & - infinite loop on address range
m2e& &&&- Restore the address and len to env from supernova's mmap
macaddr - setup EMAC MAC addr
mbup& & - mboot upgrade
md& && &- memory display
memtest - Get the performance of memory
mm& && &- memory modify (auto-incrementing address)
mmc& &&&- MMC sub system
mmcinfo - display MMC info
mmcreg&&- mmcreg show ext-csd
mscompress7- Compress or decompress lzma files
msg& &&&- print string - msg [string]
mstar& &- update kernal & root file system automatically by script file
mtest& &- simple RAM read/write test
mw& && &- memory write (fill)
net_miu - set miu setting on software upgrade
nm& && &- memory modify (constant address)
nuttxProtect- nuttx Protect&&- Protect nuttx
ota_zip_check- do OTA zip package check.
panel_init- panel_init&&- init panel by panel.ini
panel_post_init- backligth on&&- backlight on
panel_pre_init- panel_pre_init&&- init panel by panel.ini
ping& & - send ICMP ECHO_REQUEST to network host
pmProtect- runtime pm Protect&&- Protect runtime PM
pm_power_test- PM DC on/Off power test
pop_raw_io_config- pop raw_io last config
printenv- print environment variables
push_raw_io_config- push raw_io current config
raw_io_status- get raw_io status
raw_read- Read the raw datas that store in the target device
Yo have to execute 'config_raw_io' before using this cmd
raw_write- Write the raw datas that store in the target deviceYo have to execute 'config_raw_io' before using this cmd
recovery_wipe_partition- do recovery wipe data or cache.
reset& &- Perform RESET of the CPU
riu& &&&- riu&&- riu command
run& &&&- run commands in an environment variable
runtime_pm- if boot to PM
saveenv - save environment variables to persistent storage
setenv&&- set environment variables
showtb&&- Show register command table.& & -&&showtb [stage]
showvar - print local hushshell variables
sleep& &- delay execution for some time
source&&- run script from memory
spi& &&&- See SPI commands
spi2usb - Read data from spi to usb
sync_mmap- Sync the some id's address and len to env and bootargs from supernova's mmap
test& & - minimal test like /bin/sh
tftpboot- boot image via network using TFTP protocol
true& & - do nothing, successfully
udstar&&- Execute the script file that is stored in usb disk
updatemiureg- Call driver to update miu setting
usb& &&&- USB sub-system
usb2spi - write data from usb to spi
usb_bin_check- do usb bin document check.
usbboot - boot from USB device
ustar& &- ustar& &- update kernal & root file system automatically by script file
version - print monitor, compiler and linker version
Kaiser# 复制代码
阅读权限70
在线时间 小时
用编程器从FLASH（KH25L1606EM2I）中提取的固件
10:34 上传
点击文件名下载附件
下载积分: 金钱 -1
2 MB, 下载次数: 39, 下载积分: 金钱 -1
阅读权限70
在线时间 小时
按遥控器“设置”后能看到的一些界面
HDMI音频输出.jpg (108.8 KB, 下载次数: 0)
10:39 上传
SPDIF音频输出.jpg (117.19 KB, 下载次数: 0)
10:39 上传
版本信息.jpg (136.11 KB, 下载次数: 0)
10:39 上传
本地更新.jpg (150.38 KB, 下载次数: 0)
10:39 上传
操作码.jpg (126.23 KB, 下载次数: 0)
10:39 上传
关于本机.jpg (83.54 KB, 下载次数: 0)
10:39 上传
静态信息.jpg (108.86 KB, 下载次数: 0)
10:39 上传
设备信息.jpg (122.7 KB, 下载次数: 0)
10:39 上传
设置更多1.jpg (107.36 KB, 下载次数: 0)
10:39 上传
设置更多2.jpg (138.53 KB, 下载次数: 0)
10:40 上传
设置更多3.jpg (123.3 KB, 下载次数: 0)
10:40 上传
时间.jpg (104.64 KB, 下载次数: 0)
10:40 上传
网络检测.jpg (142.11 KB, 下载次数: 0)
10:40 上传
网络设置.jpg (99.44 KB, 下载次数: 0)
10:40 上传
应用管理.jpg (102.79 KB, 下载次数: 0)
10:40 上传
远程维护连接.jpg (115.34 KB, 下载次数: 0)
10:40 上传
一些硬件信息
请问你是怎么adb连上去的呢？
阅读权限70
在线时间 小时
请问你是怎么adb连上去的呢？
我目前还没用adb连接，我只是想给它整个换固件。你也是这款？
阅读权限20
在线时间 小时
很感兴趣你是怎么提取的固件？串口线我有，软件用哪个？
我是用编程器提取固件的&
阅读权限70
在线时间 小时
用TTL线不能直接安装软件，或者root么？
使用 (可批量传图、插入视频等)快速回复