来源：蜘蛛抓取(WebSpider)
时间：2017-12-25 10:18
标签：
连接开发板
CCS5.3中针对TMDSEVM6670LE设置target configuration的详解_其它编程-织梦者
当前位置:&>&&>& > CCS5.3中针对TMDSEVM6670LE设置target configuration的详解
CCS5.3中针对TMDSEVM6670LE设置target configuration的详解
转载地址：/technology/ccs-arget-configuration-setting-steps/
在本文中将详细介绍如何在Code Composer Studio (CCS)中设置target configuration。
开发板：TMDSEVM6670LE
模拟器：XDS560v2 Emulator
电源： 自带电源
Step1：在CCS 5.3中将界面切换到CCS Debug，这个按钮在软件界面的右上角。如果没有，请点击”CCS
Edit”左边的添加按钮，将CCS Debug加上去。按钮如下图所示。
Step2：点击当前界面左下角的按钮，如下图所示。弹出的界面如下图所示
Step3：在该界面单击右键，并选择New Target Configuration，如下图所示。
Step4：输入名字，还可以设置文件的存放位置（在本文中没有修改存放位置），最后单击Finish。如下图所示。
Step5：在Connection中选择Blackhawk XDS5560v2-USB System
Trace Emulator，在Board or Device后面输入过滤文字C6670（因为我的开发板上的DSP芯片是C6670），之后在下面TMS320C6670前面的复选框上打上√，单击Save和Test Connection。（注意：在单击Test Connection之前要把开发板用USB连接到电脑上并给开发板供电。）如果能够连接成功，会出现以下信息。
123456789101112131415161718192021222324252627282930313233343536373839404142434445464748495051525354555657585960616263646566676869707172737475767778798081828384858687888990919293949596979899100101102103104105106107108109110111112113114115116117118119120121122123124125126127128129130131132133134135136137138139140141142143144145146147148149150151152153154155156157158159160161162[Start]Execute the command:%ccs_base%/common/uscif/dbgjtag.exe -f %boarddatafile% -rv -o -F inform,logfile=yes -S pathlength -S integrity[Result]-----[Print the board config pathname(s)]------------------------------------C:\Users\chengkai\AppData\Local\.TI\\0\0\BrdDat\testBoard.dat-----[Print the reset-command software log-file]-----------------------------This utility has selected a 560/2xx-class product.This utility will load the program 'bh560v2u.out'.Loaded FPGA Image: C:\ti\ccsv5\ccs_base\common\uscif\dtc_top.jbcThe library build date was 'Oct3 2012'.The library build time was '22:14:17'.The library package version is '5.0.872.0'.The library component version is '35.34.40.0'.The controller does not use a programmable FPGA.The controller has a version number of '5' (0x).The controller has an insertion length of '0' (0x).The cable+pod has a version number of '8' (0x).The cable+pod has a capability number of '7423' (0x00001cff).This utility will attempt to reset the controller.This utility has successfully reset the controller.-----[Print the reset-command hardware log-file]-----------------------------The scan-path will be reset by toggling the JTAG TRST signal.The controller is the Nano-TBC VHDL.The link is a 560-class second-generation-560 cable.The software is configured for Nano-TBC VHDL features.The controller will be software reset via its registers.The controller has a logic ONE on its EMU[0] input pin.The controller has a logic ONE on its EMU[1] input pin.The controller will use falling-edge timing on output pins.The controller cannot control the timing on input pins.The scan-path link-delay has been set to exactly '2' (0x0002).The utility logic has not previously detected a power-loss.The utility logic is not currently detecting a power-loss.Loaded FPGA Image: C:\ti\ccsv5\ccs_base\common\uscif\dtc_top.jbc-----[The log-file for the JTAG TCLK output generated from the PLL]----------TestSize CoordMHzFlagResult Description~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~1 none- 01 00500.0kHz -similarisit internal clock2 none- 01 09570.3kHz -similarisit internal clock00.0kHz Ogood value measure path length00.0kHz Ogood value auto step initialD601.6kHz Ogood value auto step deltaC718.8kHz Ogood value auto step deltaE859.4kHz Ogood value auto step delta.031MHz Ogood value auto step deltaF1.234MHz Ogood value auto step delta 1F1.484MHz Ogood value auto step delta 1.781MHz Ogood value auto step delta 1.125MHz Ogood value auto step delta 1.531MHz Ogood value auto step delta 1.031MHz Ogood value auto step delta 1.625MHz Ogood value auto step delta 1.313MHz Ogood value auto step delta 1.188MHz Ogood value auto step delta 1.188MHz Ogood value auto step delta 1.438MHz Ogood value auto step delta 2.875MHz Ogood value auto step delta 20.63MHz Ogood value auto step delta 2E11.75MHz{O} good value auto step delta 2E7.875MHz Ogood value auto power initial 2E9.750MHz Ogood value auto power delta 20.75MHz Ogood value auto power delta 2A11.25MHz Ogood value auto power delta 2C11.50MHz Ogood value auto power delta 2D11.63MHz Ogood value auto power delta 2D11.63MHz Ogood value auto power delta 30.38MHz{O} good value auto margin initialThe first internal/external clock test resuts are:The expect frequency was 500000Hz.The actual frequency was 499872Hz.The delta frequency was 128Hz.The second internal/external clock test resuts are:The expect frequency was 570312Hz.The actual frequency was 569214Hz.The delta frequency was 1098Hz.In the scan-path tests:The test length was 16384 bits.The JTAG IR length was 6 bits.The JTAG DR length was 1 bits.The IR/DR scan-path tests used 30 frequencies.The IR/DR scan-path tests used 500.0kHz as the initial frequency.The IR/DR scan-path tests used 11.75MHz as the highest frequency.The IR/DR scan-path tests used 10.38MHz as the final frequency.-----[Measure the source and frequency of the final JTAG TCLKR input]--------The frequency of the JTAG TCLKR input is measured as 10.37MHz.The frequency of the JTAG TCLKR input and TCLKO output signals are similar.The target system likely uses the TCLKO output from the emulator PLL.-----[Perform the standard path-length test on the JTAG IR and DR]-----------This path-length test uses blocks of 512 32-bit words.The test for the JTAG IR instruction path-length succeeded.The JTAG IR instruction path-length is 6 bits.The test for the JTAG DR bypass path-length succeeded.The JTAG DR bypass path-length is 1 bits.-----[Perform the Integrity scan-test on the JTAG IR]------------------------This test will use blocks of 512 32-bit words.This test will be applied just once.Do a test using 0xFFFFFFFF.Scan tests: 1, skipped: 0, failed: 0Do a test using 0x.Scan tests: 2, skipped: 0, failed: 0Do a test using 0xFE03E0E2.Scan tests: 3, skipped: 0, failed: 0Do a test using 0x01FC1F1D.Scan tests: 4, skipped: 0, failed: 0Do a test using 0x5533CCAA.Scan tests: 5, skipped: 0, failed: 0Do a test using 0xAACC3355.Scan tests: 6, skipped: 0, failed: 0All of the values were scanned correctly.The JTAG IR Integrity scan-test has succeeded.-----[Perform the Integrity scan-test on the JTAG DR]------------------------This test will use blocks of 512 32-bit words.This test will be applied just once.Do a test using 0xFFFFFFFF.Scan tests: 1, skipped: 0, failed: 0Do a test using 0x.Scan tests: 2, skipped: 0, failed: 0Do a test using 0xFE03E0E2.Scan tests: 3, skipped: 0, failed: 0Do a test using 0x01FC1F1D.Scan tests: 4, skipped: 0, failed: 0Do a test using 0x5533CCAA.Scan tests: 5, skipped: 0, failed: 0Do a test using 0xAACC3355.Scan tests: 6, skipped: 0, failed: 0All of the values were scanned correctly.The JTAG DR Integrity scan-test has succeeded.[End]Step 6：依次选择Advanced -& C66xx_0(此处是选择一个核，选其他的也可以) -& Browse -& Save -& Test Connection。注意：在单击Browse时会弹出一个选择文件的对话框，我们要选择的文件路径为：
C:\ti\ccsv5\ccs_base\emulation\boards\evmc6670l\gel
这个路径根据自己安装CCS的路径而定。
如果测试通过，会出现下面的信息。
%ccs_base%/common/uscif/dbgjtag.exe
%boarddatafile%
inform,logfile=yes
pathlength
-----[Print
pathname(s)]------------------------------------
C:\Users\chengkai\AppData\Local\.TI\\
0\0\BrdDat\testBoard.dat
-----[Print
reset-command
log-file]-----------------------------
560/2xx-class
'bh560v2u.out'.
C:\ti\ccsv5\ccs_base\common\uscif\dtc_top.jbc
'22:14:17'.
'5.0.872.0'.
'35.34.40.0'.
controller
programmable
controller
controller
cable+pod
cable+pod
capability
(0x00001cff).
controller.
successfully
controller.
-----[Print
reset-command
log-file]-----------------------------
controller
second-generation-560
configured
controller
registers.
controller
controller
controller
falling-edge
controller
link-delay
previously
power-loss.
power-loss.
C:\ti\ccsv5\ccs_base\common\uscif\dtc_top.jbc
PLL]----------
CoordMHzFlagResult
Description
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
00500.0kHz
-similarisit
09570.3kHz
-similarisit
00500.0kHz
00500.0kHz
0D601.6kHz
1C718.8kHz
2E859.4kHz
021.031MHz
0F1.234MHz
10128+
1F1.484MHz
11128+
321.781MHz
12128+
042.125MHz
13128+
112.531MHz
14128+
213.031MHz
15128+
343.625MHz
16128+
054.313MHz
17128+
135.188MHz
18128+
236.188MHz
19128+
377.438MHz
20128+
078.875MHz
21128+
1510.63MHz
22128+
1E11.75MHz{O}
23512+
3E7.875MHz
24512+
0E9.750MHz
25512+
1610.75MHz
26512+
1A11.25MHz
27512+
1C11.50MHz
28512+
1D11.63MHz
29512+
1D11.63MHz
30512+
1310.38MHz{O}
internal/external
internal/external
frequencies.
frequency.
frequency.
frequency.
-----[Measure
input]--------
-----[Perform
path-length
DR]-----------
path-length
instruction
path-length
succeeded.
instruction
path-length
path-length
succeeded.
path-length
-----[Perform
IR]------------------------
0xFFFFFFFF.
0xFE03E0E2.
0x01FC1F1D.
0x5533CCAA.
0xAACC3355.
correctly.
succeeded.
-----[Perform
DR]------------------------
0xFFFFFFFF.
0xFE03E0E2.
0x01FC1F1D.
0x5533CCAA.
0xAACC3355.
correctly.
succeeded.
这样我们就创建好了Target Configuration。
以上就是CCS5.3中针对TMDSEVM6670LE设置target configuration的详解的全文介绍,希望对您学习和使用程序编程有所帮助.
这些内容可能对你也有帮助
更多可查看其它编程列表页。
猜您也会喜欢这些文章ccs不能连接到6678Le电路板 - C6000(TM)多核 - 德州仪器在线技术支持社区
ccs不能连接到6678Le电路板
发表于4年前
<input type="hidden" id="hGroupID" value="32"
电脑装完光盘附带的CCS后；打开CCs软件，新建了一个配置文件，在connection,选择的的Blackhawk xds560v2-USB System Trace Emulator,在Device,选择的是&a href=&.cn/product/cn/TMS320C6678& target=&extwin&>TMS320C6678&/a>.然后在配置文件上有键选择 Launch selected configuration.& 结果弹出下面的错误提示框：（我USB插的是上面的小板）&/p>
&p>Blackhawk& XDS560V2-USB System Trace Emulator _O/IceP...&/p>
&p>Error initializing emulator .&/p>
&p>请高手帮忙指点下。谢谢了&/p>
&p>&&/p>&div style=&clear:&>&/div>" />
ccs不能连接到6678Le电路板
此问题已被解答
All Replies
举人1110分
电脑装完光盘附带的CCS后；打开CCs软件，新建了一个配置文件，在connection,选择的的Blackhawk xds560v2-USB System Trace Emulator,在Device,选择的是.然后在配置文件上有键选择 Launch selected configuration.& 结果弹出下面的错误提示框：（我USB插的是上面的小板）
Blackhawk& XDS560V2-USB System Trace Emulator _O/IceP...
Error initializing emulator .
请高手帮忙指点下。谢谢了
You have posted to a forum that requires a moderator to approve posts before they are publicly available.
进士3060分
你好，你设备管理器上查看是否有黄色叹号？如果有更新驱动。
You have posted to a forum that requires a moderator to approve posts before they are publicly available.
状元52731分
检查驱动问题：
首先对应的连接、断开USB仿真器硬件，看PC的设备管理器中硬件驱动是否链接、断开。
再使用Sd560v2Cnfg v5工具，测试仿真器驱动是否正常。
如果您的问题得到了解决，请点击下面标签&& &是 &&&，谢谢！
You have posted to a forum that requires a moderator to approve posts before they are publicly available.
举人1110分
我试过了，当插上板子的时候，设备管理器里多了一个设备，Black XDS560v2-USB Mezzaine Emulator,确实前面有个叹号，应该是这个的驱动没装好。但是驱动程序在哪里呢？是光盘里的DPinst32.exe吗？我装了光盘附带的DPinst32.exe,结果还是没解决。驱动在哪里下呢？
You have posted to a forum that requires a moderator to approve posts before they are publicly available.
举人1110分
我断开板子后，设备管理器里硬件驱动有链接，断开，但是链接的时候，前面有个叹号，是不是驱动没有安装呢？如果没安装，那驱动程序在哪里下载？谢谢
You have posted to a forum that requires a moderator to approve posts before they are publicly available.
状元52731分
DPinst32.exe不是仿真器驱动。
仿真器驱动在CCSv5中，都是直接包含在CCS软件包里的，安装CCS的时候已经直接安装了。
如果驱动有问题，我建议你使用最新版的CCSv5.3，安装好，无需再安驱动。
http://processors./index.php/Download_CCS
如果您的问题得到了解决，请点击下面标签&& &是 &&&，谢谢！
You have posted to a forum that requires a moderator to approve posts before they are publicly available.
举人1110分
我装了CCS5.3，还是没解决，连接测试时 提示下面的错误：这是什么问题？
------【Print the reset-command software log-file】---------
This utility has selected a& 560/2xx-class product.
This utility will load the program 'bh560v2u.out'.
E_RPCENV_IO_ERROR(-6)& No& connections : emulation was not found
An error occured while soft opening the controller.
----[An error has occured and this utility has aborted]----
This error is generated by TI's USCIF driver or utilities.
The value is '-250'(oxffffff06)
The title is 'SC_ERR_ECOM_EMVNANE'.
The explanation is :
An attempt to access the named emulator via USCIF ECOM has failed.
You have posted to a forum that requires a moderator to approve posts before they are publicly available.
请问你的这个问题解决了么？
我现在也遇到这个问题了，不知道怎么解决。
You have posted to a forum that requires a moderator to approve posts before they are publicly available.求助大神，CCS连接不上6670LE开发板 - C6000(TM)多核 - 德州仪器在线技术支持社区
求助大神，CCS连接不上6670LE开发板
发表于3年前
<input type="hidden" id="hGroupID" value="32"
软件环境：CCS5.2&/p>
&p>硬件环境：6670LE开发板，XDS560v2板上仿真器&/p>
&p>问题描述：&/p>
&p>1、Launch目标板配置文件，load GEL文件后，Connect Target失败，提示错误：&/p>
&p>Error Connecting to the target：(Error -503@0x0)The user selected phase-one auto-range frequency failed the scan-path test.The utility or debugger requested the JTAG controller and cable,that generate the JTAG clock,to use a user selected feature or algorithm.详细内容见附件。&/p>
&p>2、在目标板配置文件中测试连接，提示错误内容基本一致。&/p>
&p>This error is generated by TI&s USCIF driver or utilities.&/p>
&p>The value is&-503&(0xfffffe09).&/p>
&p>The title is 'SC_ERR_TEST_AUTOMATIC1'&/p>
&p>详情见附件&/p>
&p>3、电源打开后，仿真器指示灯显示是正确的。&/p>
&p>4、重新升级过XDS560的firmware，错误仍然存在。&/p>
&p>&div style=&clear:&>&/div>" />
求助大神，CCS连接不上6670LE开发板
此问题尚无答案
All Replies
软件环境：CCS5.2
硬件环境：6670LE开发板，XDS560v2板上仿真器
问题描述：
1、Launch目标板配置文件，load GEL文件后，Connect Target失败，提示错误：
Error Connecting to the target：(Error -503@0x0)The user selected phase-one auto-range frequency failed the scan-path test.The utility or debugger requested the JTAG controller and cable,that generate the JTAG clock,to use a user selected feature or algorithm.详细内容见附件。
2、在目标板配置文件中测试连接，提示错误内容基本一致。
This error is generated by TI&s USCIF driver or utilities.
The value is&-503&(0xfffffe09).
The title is 'SC_ERR_TEST_AUTOMATIC1'
详情见附件
3、电源打开后，仿真器指示灯显示是正确的。
4、重新升级过XDS560的firmware，错误仍然存在。
You have posted to a forum that requires a moderator to approve posts before they are publicly available.
补充一下问题的附件
You have posted to a forum that requires a moderator to approve posts before they are publicly available.
状元60945分
先确认一下你的硬件连接，你拿到的EVM板是EVM6670LE， 上面有一个小的子板，在连接时需要把mini-USB连接到上面子卡的usb上。
You have posted to a forum that requires a moderator to approve posts before they are publicly available.
硬件连接应该没问题的，我已经使用了一段时间了，之前都是正常工作的，usb之类的我也换过，都是同样的错误。
补充下问题出现的情形：运行程序过程中，突然出问题的，后面再连接就一直提示这错误
You have posted to a forum that requires a moderator to approve posts before they are publicly available.3被浏览214分享邀请回答0添加评论分享收藏感谢收起0添加评论分享收藏感谢收起写回答
